Demilec Attic Cleaning & Rodent Proofing Nationwide

Demilec Attic Cleaning & Rodent Proofing in Campbell: What to Know First

We provide independent Demilec attic cleaning and rodent proofing in Campbell, typically completing jobs in one to two days with a written price before any work starts. Most Demilec systems we encounter in Campbell homes are running with compromised air barriers or active rodent damage that the owner didn’t notice until utility bills climbed or odors appeared. As an independent Demilec service provider, we carry no manufacturer affiliation, which means our recommendations are based on what your specific assembly needs, not on warranty quotas or dealer incentives.

Call (831) 534-3206

This page is for Campbell homeowners who know they have Demilec insulation or spray foam in their attic and suspect rodent intrusion, contamination, or air-sealing failure. If you’re seeing droppings, compressed or stained foam, or smelling ammonia near your hatch, we can diagnose it and give you a flat written price. Call (831) 534-3206.

How Demilec Products Fail - and How We Fix Them

• Heatlok HFO Pro exposed to prolonged rodent nesting - The open-cell structure of this series traps urine and organic matter deep in the matrix, making surface cleaning ineffective. We remove the contaminated sections entirely, then re-apply only after the substrate is sanitized and proofed. In Campbell’s dry summers, crystallized waste becomes airborne when disturbed; we use HEPA containment during removal.
• Heatlok XT spray foam separating from top plates after rodent tunneling - Rodents exploit the gap between foam and framing to create runs that bypass the air barrier entirely. We find these separations with smoke pencil testing, cut back the compromised foam, re-seal the plate with closed-cell repair foam, then overlay with mechanical barrier where rodent pressure is high.
• Demilec open-cell foam sagging in rafter bays above contaminated attics - Moisture from rodent activity degrades the adhesive bond to OSB or plywood sheathing. We see this in Campbell’s older ranch homes near the Winchester corridor, where roof decks are often unvented and any added humidity loads the assembly. We remove the failed foam, dry the sheathing with targeted airflow, then re-apply with corrected vapor strategy.
• Heatlok HFO High Lift developing surface mold after inadequate cleaning - Previous contractors sometimes sanitize only the visible surface, leaving organic material in the foam cells. The mold returns within a season. We use enzyme-based decontamination followed by borated treatment on adjacent wood, then verify with moisture meters before declaring the cavity ready.
• Demilec foam compromised by DIY rodenticide placement - Homeowners often stuff poison into foam gaps, creating toxic dust that circulates through HVAC returns. We remove the chemically contaminated foam sections, clean the cavity with HEPA vacuum and botanical sanitizer, and reinstall with proper exclusion mesh at all penetration points. The fix costs more than doing it right the first time.

Our Demilec Attic Cleaning & Rodent Proofing Process

1. 1
   Written price before entry - We inspect from the hatch with borescope cameras and moisture meters, then deliver a flat price with scope and warranty in writing. No work starts without your signature on both documents.
2. 2
   Containment and negative air setup - We seal the attic hatch and establish HEPA-filtered negative pressure before disturbing any material. This is non-negotiable on Demilec jobs because open-cell foam releases particulate when cut.
3. 3
   Targeted removal and substrate assessment - We remove only the compromised foam and soiled insulation, marking sound material for retention. Every removed section is photographed; every retained section is documented with moisture and density readings.
4. 4
   Sanitization and structural repair - Enzyme treatment on organic contamination, mechanical repair of chewed wiring or damaged sheathing, and installation of galvanized exclusion mesh at all known entry points. We use 1/4-inch hardware cloth, not the flimsy stuff that squirrels pull through in two seasons.
5. 5
   Reinstallation with blower-door verification - New Demilec or compatible foam is installed to original specification, followed by blower-door testing to confirm the attic plane is sealed. You receive printed before-and-after CFM50 numbers, photos of all work, and the written warranty.

Before

After

What Demilec Attic Cleaning & Rodent Proofing Costs in Campbell

Campbell’s tight housing stock and older roof geometries often add labor hours compared to new construction in San Jose. We price for the actual conditions we find, not a flat rate that assumes your attic matches a spreadsheet. Call (831) 534-3206 for a written estimate - there’s no charge, and we provide a free second opinion on any competing quote you bring us.

Why Campbell Homeowners Call Topside Attic Insulation Campbell for Demilec Work

We’ve been in Campbell long enough to know which roof pitches near the Pruneyard Plaza corridor hide rodent access that inspectors miss, and which vent configurations in the 95008 zip create the humidity loads that degrade Demilec foam from the inside. Wes Okafor runs a blower-door test on every job - pressurization readings in CFM50, printed and handed to you - so you can verify the air-sealing result yourself rather than taking our word for it.

Our 365-Day Done Right Promise applies to all Demilec work: if the rodents return through a gap we sealed, or if foam separation reappears at our repair boundary, we fix it at no charge. We also service Reflectix radiant barrier systems, which matters because many Campbell homes layered Demilec foam under Reflectix and need a technician who understands both assemblies. Calls are answered by a live person 24/7, and our technicians arrive in uniform with background checks on file.

Seal the leaks first. The insulation has nowhere useful to go until you do.

FAQs